This ice cream wafer cone machine is specially designed to make various shapes and sizes of ice cream cone, good quality and easy to operate.
(1) frame: the frame is welded with profile, and the surrounding surface is steel plate. Upper bearing mold, the mold is equipped with sliding way, to facilitate the outflow of finished products, and also have the function of insulation. Electrical boxes are installed at the bottom. The upper part of the frame is set with a pendulum mechanism. The front end of the swinging rod is the upper mould of the mold, and the back end is connected to the spring to balance the weight of the mold.
(2) mold: composed of upper and lower modules. The upper module is installed with the core head, and it is suspended under the swing rod to move around the bracket. The lower die corresponds to the upper die flat on the rack. The lower die is divided into three (gg - 32 type is divided into 5), the middle plate is fastened to the frame, and the edge plate can be shifted. When closed, it becomes a whole. At this time, the upper mold is covered, and each core head enters the cavity to form a cavity, and the injected pulp is molded into an egg holder shape. After lifting up the mold, separate the mold to form a certain distance, allowing the finished egg to fall, and also easy to clean.
The mould has longitudinal holes in each system, and the heating tube is inserted into the heating tube. It is the heat source of the baked egg. In order to prevent the electric heat pipe loose, the mould has the screw to tighten the electric heat pipe.
The lower die has a traction handle on each end, and the front of the handle is pushed in the front of the handle, and then the lower part is pulled apart. In front of the mold, the center is the locking mechanism, also equipped with the handle, the handle is rotated, and the next mold can be locked.
In front of the upper mold, the other handle, with the upper mold locking mechanism one body, lower pressure and the right rotation can lock the mold, the left hand side of the upward pressure can open up the mold.
(3) electrical part: the electric control element is concentrated in the drawer below the rack, and the loose screw can be pulled out as a whole. The function of this part is:
1. Introduction and protection of power supply;
2. Adjust and control the working temperature of the mold so that it is constant within the range.
3. Cooperate with the travel switch on the upper part of the frame, and through time relay and electric bell, it is reported that the baking time has arrived, and the finished product can be opened.
(1) frame: the frame is welded with profile, and the surrounding surface is steel plate. Upper bearing mold, the mold is equipped with sliding way, to facilitate the outflow of finished products, and also have the function of insulation. Electrical boxes are installed at the bottom. The upper part of the frame is set with a pendulum mechanism. The front end of the swinging rod is the upper mould of the mold, and the back end is connected to the spring to balance the weight of the mold.
(2) mold: composed of upper and lower modules. The upper module is installed with the core head, and it is suspended under the swing rod to move around the bracket. The lower die corresponds to the upper die flat on the rack. The lower die is divided into three (gg - 32 type is divided into 5), the middle plate is fastened to the frame, and the edge plate can be shifted. When closed, it becomes a whole. At this time, the upper mold is covered, and each core head enters the cavity to form a cavity, and the injected pulp is molded into an egg holder shape. After lifting up the mold, separate the mold to form a certain distance, allowing the finished egg to fall, and also easy to clean.
The mould has longitudinal holes in each system, and the heating tube is inserted into the heating tube. It is the heat source of the baked egg. In order to prevent the electric heat pipe loose, the mould has the screw to tighten the electric heat pipe.
The lower die has a traction handle on each end, and the front of the handle is pushed in the front of the handle, and then the lower part is pulled apart. In front of the mold, the center is the locking mechanism, also equipped with the handle, the handle is rotated, and the next mold can be locked.
In front of the upper mold, the other handle, with the upper mold locking mechanism one body, lower pressure and the right rotation can lock the mold, the left hand side of the upward pressure can open up the mold.
(3) electrical part: the electric control element is concentrated in the drawer below the rack, and the loose screw can be pulled out as a whole. The function of this part is:
1. Introduction and protection of power supply;
2. Adjust and control the working temperature of the mold so that it is constant within the range.
3. Cooperate with the travel switch on the upper part of the frame, and through time relay and electric bell, it is reported that the baking time has arrived, and the finished product can be opened.
About this wafer cone making machine, if you need, please contact with my email lisa@machinehall.com for the machine price and details.
http://www.icecreamconemachine.com/product/wafer/cone-biscuit-maker.html
ReplyDelete