The ice cream cone machine can make 12 cone per time, and the time is need baking 1 to 2 minutes, the finished product is delicious, and with good appearance.
(1) Department of welding machine: a framework for the surrounding surface with steel plate. The upper part carries the mould, and the mould is provided with a slide way to facilitate the outflow of the finished product, and also has the function of heat insulation. The bottom is equipped with electrical boxes. The upper end of the pendulum rod is the upper die of the die, and the rear end is connected with the spring, so as to balance the weight of the die.
(2) the die is composed of the upper die and the lower die. The upper die is centrally installed, and the suspension is mounted on the bracket under the swinging rod; the lower die corresponds to the upper die and is placed on the frame. The lower die is further divided into three, the middle plate is fastened on the frame, and the side plate can be moved. When the joint is closed, the upper die is covered, and each core head enters the die cavity to form a cavity, and the injected surface pulp is pressed into the shape of the egg holder; the upper mould is separated from the lower mould to form a certain spacing, so that the finished egg is laid down and the cleaning is made.
A longitudinal long hole is formed in the mold body, and the heating tube is inserted and energized to generate heat, which is the heat source of the baking egg holder. In order to prevent the electric heating tube from loosening, the mould has screws to fasten the electric heating tubes.
The two ends of the lower die are respectively provided with a traction handle, and the two handles are pushed at the same time, and the lower die is separated from each other before pushing. The front part of the lower die is a locking mechanism, and also has a handle. The handle is screwed up and the lower die can be locked after closing.
The front of the upper die is additionally provided with a handle, which is integrated with the upper mould locking mechanism, and the die can be locked under the lower pressure and the right hand, and the upper die can be opened after the left side is lifted upwards.
(3) electrical parts: electronic components single centrally mounted below the machine frame drawer, loosen screws can be pulled out completely. The function of this part is:
1, the introduction and protection of power;
2. Adjust and control the working temperature of the die so as to keep it within the range of adjusting.
3, and the travel switch at the top of the frame after the match, the time relay and the alarm bell, the baking time is up, you can mold unloading of finished products.
(1) Department of welding machine: a framework for the surrounding surface with steel plate. The upper part carries the mould, and the mould is provided with a slide way to facilitate the outflow of the finished product, and also has the function of heat insulation. The bottom is equipped with electrical boxes. The upper end of the pendulum rod is the upper die of the die, and the rear end is connected with the spring, so as to balance the weight of the die.
(2) the die is composed of the upper die and the lower die. The upper die is centrally installed, and the suspension is mounted on the bracket under the swinging rod; the lower die corresponds to the upper die and is placed on the frame. The lower die is further divided into three, the middle plate is fastened on the frame, and the side plate can be moved. When the joint is closed, the upper die is covered, and each core head enters the die cavity to form a cavity, and the injected surface pulp is pressed into the shape of the egg holder; the upper mould is separated from the lower mould to form a certain spacing, so that the finished egg is laid down and the cleaning is made.
A longitudinal long hole is formed in the mold body, and the heating tube is inserted and energized to generate heat, which is the heat source of the baking egg holder. In order to prevent the electric heating tube from loosening, the mould has screws to fasten the electric heating tubes.
The two ends of the lower die are respectively provided with a traction handle, and the two handles are pushed at the same time, and the lower die is separated from each other before pushing. The front part of the lower die is a locking mechanism, and also has a handle. The handle is screwed up and the lower die can be locked after closing.
The front of the upper die is additionally provided with a handle, which is integrated with the upper mould locking mechanism, and the die can be locked under the lower pressure and the right hand, and the upper die can be opened after the left side is lifted upwards.
(3) electrical parts: electronic components single centrally mounted below the machine frame drawer, loosen screws can be pulled out completely. The function of this part is:
1, the introduction and protection of power;
2. Adjust and control the working temperature of the die so as to keep it within the range of adjusting.
3, and the travel switch at the top of the frame after the match, the time relay and the alarm bell, the baking time is up, you can mold unloading of finished products.
http://www.icecreamconemachine.com/product/wafer/ice-cream-cone-machine12.html website
ReplyDelete